Diamond Coated Wire Drawing Dies

Diamond Coated Wire Drawing Dies
Product Introduction:
A diamond coated wire drawing die — also called a CVD nano-diamond coated die or simply nano die — is a precision drawing tool in which an ultra-hard nanocrystalline diamond layer is deposited onto the bore surface of a tungsten carbide die by Chemical Vapor Deposition (CVD).

The coating is engineered as two functional layers:
1. A micro-scale diamond layer — bonded directly to the carbide for maximum adhesion and load support;
2. A nano-scale diamond layer (20–50 nm grains) — polished to a mirror finish for minimal friction and a flawless wire surface.
Send Inquiry
Description
Technical Parameters

The CVD process takes place in a vacuum chamber: a carbon-source gas and hydrogen are introduced under high temperature and low pressure, decomposing into active carbon atoms that deposit diamond-phase carbon directly onto the carbide substrate. Plasma-assisted deposition and magnetic field control keep the coating uniform - even in deep bores down to 0.30 mm.

 

The result is a wear surface that:

 

Eliminates material adhesion - diamond has near-zero chemical affinity to aluminium and copper, so pick-up, galling and metal buildup simply do not occur;

Holds geometry - the coating does not wear into ovality the way a cobalt matrix does, keeping bore diameter and roundness stable across long campaigns;

Cuts drawing force - the nano-smooth surface lowers contact resistance, reducing pull-block load, energy consumption and wire breakage;

Survives heat - binder-free diamond stays dimensionally stable in high-temperature and high-speed drawing where carbide degrades.

 

Diamond Coated vs Carbide vs PCD

 

Attribute

Diamond Coated (CVD nano-diamond)

Tungsten Carbide

PCD

Wear surface

CVD nano-diamond, binder-free

WC-Co composite

Sintered diamond + Co binder

Relative die life

10–20× carbide

1× (baseline)

High at mid-large sizes

High-temperature capability

800–950 °C, stable

Limited

Constrained by Co binder

Wire surface finish

Mirror (Ra ≤ 0.04 μm)

Good

Very good

Material adhesion (Al/Cu pickup)

Near zero

Prone to pickup

Low

Typical wire range

0.30–50 mm

0.15–50 mm

0.05–30 mm

Cost position

Moderate premium over carbide

Lowest

Premium

Best for

Steel & welding wire, cable stranding/compacting, high-volume non-ferrous

General purpose, low-volume runs

High-abrasion, high-throughput drawing

 

Applications

Steel and alloy wire

High-, medium- and low-carbon steel wire

Stainless steel wire and welding wire

Spring wire, fastener wire, tire cord and saw wire

Non-ferrous wire

Copper, aluminium, molybdenum and other non-ferrous wire

High-conductivity copper and heavy-duty aluminium alloy profiling

Cable and conductor manufacturing

Stranding dies and compacting dies for conductor production

Bunching, compaction and tube drawing operations

Overhead and power cable conductor cores - the burr-free surface suppresses partial discharge and helps conductors pass high-voltage corona and withstand tests

Diamond Coated Wire Drawing Dies

Is DCD the Right Choice for Your Line?

 

Diamond coated dies are the strongest value when you run volume production with downtime costs. They are not always the answer:

 

Your situation

Recommended choice

High-volume steel, welding wire, stainless

Diamond coated dies

Cable stranding / compacting, burr-sensitive conductors

Diamond coated dies

High-volume copper / aluminium with pickup problems

Diamond coated dies

Short runs, low volume, cost-sensitive

Standard carbide dies

Mid-to-large diameter, maximum abrasion throughput

PCD dies

Ultra-fine wire below 0.3 mm, mirror-critical

Natural diamond or MCD dies

 

FAQ

What wire sizes are available in diamond coated dies?

The standard range is 0.30 to 50 mm finished wire diameter, with custom sizes on request. Bore uniformity is maintained even in deep bores down to 0.30 mm.

 

Can diamond coated dies replace my existing carbide dies?

Yes. They are manufactured to standard carbide geometry and casing dimensions, so they retrofit directly into your existing die holders and machines without modification.

 

Which materials can be drawn with diamond coated dies?

Carbon steel, stainless steel, welding wire, spring and fastener wire, tire cord, copper, aluminium, molybdenum and other ferrous and non-ferrous wires - including tube drawing, stranding and compacting operations.

 

Are diamond coated dies suitable for high-temperature drawing?

Yes. Because the coating contains no metal binder, it remains stable at 800–950 °C, supporting higher drawing speeds than binder-containing die materials.

 

 

 

 

Hot Tags: diamond coated wire drawing dies, China diamond coated wire drawing dies manufacturers, suppliers, factory, Nano Diamond Coated Dies, ndcd dies, NDCD Wire Drawing Dies, Synthetic Diamond Wire Drawing Dies for Precious Metal Wire

Send Inquiry